Acta Univ. Agric. Silvic. Mendelianae Brun. 2014, 62(5), 869-874 | DOI: 10.11118/actaun201462050869

The Risk Assessment at the Workplace of Assembly Operation

Marek Burda1, Martin Kotus1, Mária Burdová1, Tomáš Holota1, Tomáš Pauliček1, Martin Zach2
1 Department of Quality and Engineering Technologies, Faculty of engineering, Slovak University of Agriculture in Nitra, Tr. A. Hlinku 2, 949 76 Nitra, Slovak Republic
2 Expert Engineering Department, Institute of Lifelong Learning, Mendel University in Brno, Zemědělská 1, 613 00 Brno, Czech Republic

Risk Assessment Process by FMEA method involve hazard identification, risk assessment and risk control processes and their input is fundamental to a successful EH&S system. This Risk assessment tool follows the general process and requirements of the Health and Safety Risk Assessment Procedure.

Keywords: risk assessment, safety, FMEA, manufacturing process

Published: December 2, 2014  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Burda, M., Kotus, M., Burdová, M., Holota, T., Pauliček, T., & Zach, M. (2014). The Risk Assessment at the Workplace of Assembly Operation. Acta Universitatis Agriculturae et Silviculturae Mendelianae Brunensis, 62(5), 869-874. doi: 10.11118/actaun201462050869
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. BUJNA, M., HRAŠKOVÁ, Z. 2011. Identifikácia a analýza ohrozenia pre výrobný proces rámu. In: Bezpečnosť - kvalita - spoľahlivosť. Košice: TU. 15-20. Go to original source...
    2. BUJNA, M., KOTUS, M., ČIČO, P. 2013. Manažérstvo rizika. Nitra: SPU.
    3. BURDA, M., ČIČO, P., BUJNA, M. 2010. Posúdenie rizika pracovného miesta komplexnou metódou. In: Kvalita a spoľahlivosť technických systémov 2010. Nitra: SPU. 61-65.
    4. FÖLDEŠIOVÁ, D., KORENKO, M., FERANCOVÁ, M., KAPLÍK, P. 2013. Analysis of risk using FMEA. Advanced Materials Research, 801(special iss.): 81-85. DOI: 10.4028/www.scientific.net/AMR.801.81 Go to original source...
    5. VISTEON INTERIORS SLOVAKIA, s. r. o. 2011. Health and Safety Risk Assessment Procedure. Internal directive. Nitra.
    6. HRUBEC, J., ŽARNOVSKÝ, J. et al. 2009. Integrovaný manažérsky systém. Nitra: SPU.
    7. KREDATUSOVÁ, M., BUJNA, M. 2010. Identifikácia a analýza ohrozenia vo vybranom procese. In: Najnovšie trendy v poľnohospodárstve, v strojárstve a odpadovom hospodárstve. Nitra: SPU. 146-152.
    8. MATEIDES, A. et al. 2006. Manažérstvo kvality: história, koncepty, metódy. Bratislava: Ing. Miroslav Mračko.
    9. LESTYÁNSZKA, K. 2012. The statistical regulation of the turning process. Research papers Faculty of Materials Science and Technology Slovak University of Technology in Trnava, 20(special issue): 81-85. Go to original source...

    This is an open access article distributed under the terms of the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License (CC BY NC ND 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content