Acta Univ. Agric. Silvic. Mendelianae Brun. 2011, 59(5), 137-144 | DOI: 10.11118/actaun201159050137

The possibilities for measurement of saw blades wearing

Ján Kováč, Jozef Krilek
Katedra lesnej a mobilnej techniky, Fakulta environmentálnej a výrobnej techniky, Technická univerzita vo Zvolene, T. G. Masaryka 24, 960 53 Zvolen, Slovenská republika

Some effects come into the practice because of decreasing quality of a cutting knife. These effects then influence the whole cutting process. The paper deals with analysis of methods for evaluation of a chain saw wearing. It is necessary to know the methods for measurement of a chain saw wearing because the tool wearing has significant influence on the whole system acting i.e. machine-tool-work piece. The measurement of wearing rate was realized to obtain knowledge about the wearing rate of cutting knives on chain saws. The goal of measurement was to design suitable methods for evaluation of wearing and definition of exactness for used methods. The exactness of used methods is evaluated according to the range of variance. The cutting knife wearing was analyzed by two methods; the results of both methods were compared. In the future it would be very effective to generalize mentioned methodology for measurement of a cutting knife wearing.

Keywords: cutting process, measurement methods, wear, saw blades, wood cutting

Received: April 12, 2011; Published: March 23, 2014  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Kováč, J., & Krilek, J. (2011). The possibilities for measurement of saw blades wearing. Acta Universitatis Agriculturae et Silviculturae Mendelianae Brunensis, 59(5), 137-144. doi: 10.11118/actaun201159050137
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. BUDA, J., SOUČEK, J., VASILKO, K., 1983: The theory of machining. SNTL Praha 1983. 145 s. In Slovak.
    2. KOVÁČ, J., MIKLEŠ, M., 2009: Analysis a cutting edge geometry influence on circular saw teeth at the process of crosscutting wood. International scientific magazine Acta Universitas Agriculturae et Silviculturae Mendelianae Brunensis. 57, 4: 177-183. ISSN 1211-8516. In Slovak. Go to original source...
    3. LISIČAN, J., 1996: The theory and technique for processing wood. TU Zvolen: MATCENTRUM. 626 s. ISBN 80-967315-6-4. In Slovak.
    4. NOVÁČEK, E., NOVÁK, V., 2006: Possibilities for measurement of a tool wearing. In: Trendy lesníckej, drevárskej a environmentálnej techniky a jej aplikácie vo výrobnom procese. Medzinárodná vedecká konferencia, sekcia č. 1 Lesná, mobilná a drevárska technika, Zvolen. 4.-6. September. 330-335. ISBN 80-228-1648-5. In Slovak.
    5. PROKEŠ, S., 1980: Machining wood and new materials from wood. Praha: SNTL. 369 s. In Czech.
    6. ROUSEK, M., 2004: The specific problems of high speed machining of wood. 1. vyd. Brno: Mendelova zemědělská a lesnická univerzita, Folia Universitatis Agriculturae et Silviculturae Mendelianae Brunensis. 67 s. ISBN 80-7157-859-2. In Czech.
    7. ROUSEK, M., KOPECKÝ, Z., NOVÁK, V., 2009: Results of research into high-speed milling. [CD-ROM]. In Forest, Wildlife and Wood Sciences for Society Development. 451-460. ISBN 978-80-213-2019-2. In Czech.

    This is an open access article distributed under the terms of the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License (CC BY NC ND 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content