Acta Univ. Agric. Silvic. Mendelianae Brun. 2005, 53(5), 175-186 | DOI: 10.11118/actaun200553050175
Vliv tepelného zpracování na abrazivní opotřebení
- Ústav techniky a automobilové dopravy, Mendelova zemědělská a lesnická univerzita v Brně, Zemědělská 1, 613 00 Brno, Česká republika
Diskutované výsledky experimentálních prací jednoznačně potvrdily, že odolnost materiálu pracovního tělesa je funkcí převážně jeho tvrdosti. Tento závěr potvrzuje shoda výsledků z pracovního experimentu v půdě s výsledky provedenými na brusném plátně dle ČSN 01 5084. Tzn., že největší tvrdost a nejmenší opotřebení byly zjištěny u vzorku, který byl zakalen, zatímco u vzorku žíhaném na měkko je opotřebení v obou případech největší. Úbytky tloušťky jsou i z hlediska vizuálního pozorování kumulovány do spodní části vzorku, tj. místa, kde naráží volné částice půdního abraziva. Tímto dochází k významnému rýhování a tím i značnému úbytku materiálu.
Předkládaná práce potvrzuje vliv strukturního složení oceli (v závislosti na jeho tepelném zpracování) na odolnost proti abrazi. Z uvedeného plyne mimořádná důležitost volby materiálu a jeho následné strukturní modifikace jako funkce hodnoty degradačního procesu v konkrétním půdním prostředí. Rozhodnutí ovlivňuje nejen predikci životnosti součásti, ale i celého zařízení z hlediska ekonomického hodnocení jeho provozu.
abrazivní opotřebení, orba, tepelné zpracování, ocel
Influence of heat treatments on the abrasive wear
The particular samples were made of the steel 14 260 and were exposed to following different heat treatments - soft annealing, normalizing, heat refining and hardening. After these heat treatments the samples were exposed both laboratory tests and also field tests. The wear test particles was carried out on the device with abrasive canvas. The laboratory test was realized in room temperature and normal atmospheric pressure. Measured values were statistically and graphically analyzed and interpreted. Results of the tests confirmed our preliminary expectations that the extent of the wear would depend on the value of hardness of the used materials. The hardest structure of the hardened steel had the smallest material decrease compared to the largest decrease of the soft annealing steel.
Tested samples were fixed to a cutting edge of a ploughing aggregate which performed work in previously determined sector area. At intervals of each 400 meters there were measured decreases of weights and surfaces of the samples and consequently were evaluated and graphically interpreted relating abrasive wear of the particular samples. Also in this test the results form previous laborator test were confirmed and the smallest wear had the hardened steel samples.
On the basis of the measured values we can deduce the high importance of the right choice of the adequate material which is able to resist to the wearing process best. This decision will significantly affect not only the length of the service life of the particular parts but also the whole machinery as well as its economic operation.
Keywords: abrasive wear, tillage, heat treatments, Czech Standard steel 14 260
Received: July 29, 2005; Published: December 22, 2014 Show citation
References
- Havlíček, J. a kol.: Provozní spolehlivost strojů. SZN Praha, 1989. 610 s., ISBN 80-209-0029-2.
- Neubauer, K. a kol.: Stroje pro rostlinnou výrobu. SZN Praha, 1987. 720 s., ISBN 80-209-0075-6.
- Blaškovič, P. Balla, J. Dzimko, M.: Tribológia. ALFA Bratislava, 1990. 360 s., ISBN 80-05-006330.
- Pluhař, J. a kol.: Nauka o materiálu. SNTL Praha, 1989. 522 s.
- Jech, J.: Tepelné zpracování oceli. SNTL Praha, 1977. 400 s.
- ČSN 01 5084: Stanovení odolnosti kovových materiálů proti opotřebení na brusném plátně.
- ČSN 01 5050: Opotřebení materiálu - názvosloví.
This is an open access article distributed under the terms of the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License (CC BY NC ND 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.