Acta Univ. Agric. Silvic. Mendelianae Brun. 2016, 64(2), 467-471 | DOI: 10.11118/actaun201664020467

Safety Audit of Band Saw in Manufacturing Organization

Martin Kotus1, Erika Jankajová1, Katarína Lestyánszka ©kůrková2, Darina Matisková3, Martin Zach4
1 Department of Quality and Engineering Technologies, Faculty of Engineering, Slovak University of Agriculture in Nitra, Tr. A. Hlinku 2, 949 76 Nitra, Slovak Republic
2 Institute of Safety, Environment and Quality, Faculty of Materials Science and Technology in Trnava, Slovak University of Technology in Bratislava, Botanická 49, 917 24 Trnava, Slovak Republic
3 Department of Manufacturing Management, Faculty of Manufacturing Technologies with a seat in Preąov, Technical University of Koąice, Bayerova 1, 080 01 Preąov, Slovak Republic
4 Expert Engineering Department, Institute of Lifelong Learning, Mendel University in Brno, Zemědělská 1, 613 00 Brno, Czech Republic

This paper deals with the verifying of safety status for a selected device in the manufacturing organization. The safety audit of band saw was realized in the manufacturing process. Safety requirements of the machinery for cutting material are given in the standard STN 20 0723. This standard from the point of view of the work safety defines selected requirements for sawing, cutting compounds and the using of prevention to work with cutting compounds. Among the basic requirements belong material clamping and security services for cut, band saws and jaws wear, as well as the required protective cover. The efficiency of audit in percentage was evaluated by the level of fulfilment as follows: fulfilled (A) mostly fulfilled (AB), conditionally fulfilled (B) or unfulfilled (C). Through safety audit, were defined the weaknesses that increase the degree of employee health hazard. There were proposed corrective actions to eliminate weaknesses and retraining employees. It is still needed to perform the safety audit due to reduction of the probability of occupational injury.

Keywords: occupational safety, risk, health hazard, danger

Prepublished online: May 4, 2016; Published: May 1, 2016  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Kotus, M., Jankajová, E., Lestyánszka ©kůrková, K., Matisková, D., & Zach, M. (2016). Safety Audit of Band Saw in Manufacturing Organization. Acta Universitatis Agriculturae et Silviculturae Mendelianae Brunensis, 64(2), 467-471. doi: 10.11118/actaun201664020467
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. ANDRÁSSYOVÁ, Z., HRUBEC, J., BAS CERDA, M. C. 2013. Improvement of manufacturing process quality according to final inspection results. Acta Technologica Agriculturae, 2: 47-50. DOI: 10.2478/ata-2013-0012 Go to original source...
    2. BUJNA, M., KREDATUSOVÁ, M., BURDA, M. 2010. Identifikácia a analýza ohrozenia pre výrobný proces loľiska. In: Kvalita a spoµahlivos» technických systémov. Nitra: SPU.
    3. BURDA, M., ČIČO, P., BUJNA, M. 2010. Posúdenie rizika pracovného miesta komplexnou metódou. In: Kvalita a spoµahlivos» technických systémov 2010. Nitra: SPU.
    4. GIRMANOVÁ, L., MIKLO©, V., PALFY, P., PETRÍK, J., SÜTŐOVÁ, A., ©OLC, M. 2009. Nástroje a metódy manaľérstva kvality. Koąice: TU Elfa.
    5. HNILICA, R., JANKOVSKÝ, M., DADO, M., MESSINGEROVÁ, V. 2013. Experimental evaluation of combined effects of risk factors in work environment. In: Engineering for Rural Development 2013. Jelgava: Latvia University of Agriculture.
    6. KONSTANCIAK, M. 2012. Analysis of technological strategies on the example of the production of the tramway wheels. Archives of Materials Science and Engineering, 57(2): 69-74.
    7. KREDATUSOVÁ, M., BUJNA, M. 2010. Identifikácia a analýza ohrozenia vo vybranom procese. In: Najnovąie trendy v poµnohospodárstve, v strojárstve a odpadovom hospodárstve. Nitra: SPU.
    8. MURA, L. 2011. Vąeobecná ekonomická teória. Bratislava: CRR.SK.
    9. MURA, L. 2012. Úvod do podnikania. Komárno: Univerzita J. Selyeho.
    10. PÍĄA, J., ADAMČIK, F., KORBA, P., ANTO©KO, M. 2014. Safety Hazard and Risk in Slovak Aviation Regulations. Our Sea, International Journal of Maritime Science and Technology, 61(1-2): 27-30.
    11. SELEJDAK, J., KONSTANCIAK, M. 2012. Practical use of quality instruments in rails production process. Hutnik - Wiadomo¶ci Hutnicze, 79(12): 952-955.
    12. ÚNMS SR. 1988. Obrábacie stroje na kovy. Bezpečnostné poľiadavky na stroje na delenie materiálu. STN 20 0723. Bratislava: ÚNMS SR.
    13. ÚNMS SR. 2011. Bezpečnos» strojov. Vąeobecné zásady konątruovania strojov. Posudzovanie a zniľovanie rizika. STN EN ISO 12100. Bratislava: ÚNMS SR.
    14. ©OLC, M., MARKULIK, ©., GRAMBALOVÁ, E. 2013. Quality of refractory materials in the technological process. Advanced Materials Research, 524(527): 2026-2030. Go to original source...
    15. VOTAVA, J. 2013a. Influence of edge radius of sintered-carbide tip on roughness of machined surface. Acta Universitatis Agriculturae et Silviculturae Mendelianae Brunensis, 61(5): 1497-1504. DOI: 10.11118/actaun201361051497 Go to original source...
    16. VOTAVA, J. 2013b. Influence of roughness of machined surface on adhesion of anticorrosion system. Acta Universitatis Agriculturae et Silviculturae Mendelianae Brunensis, 61(6): 1889-1896. DOI: 10.11118/actaun201361061889 Go to original source...
    17. VOTAVA, J. 2013c. Protection of welded joints against corrosion degradation. Acta Universitatis Agriculturae et Silviculturae Mendelianae Brunensis, 61(6): 1897-1904. DOI: 10.11118/actaun201361061897 Go to original source...

    This is an open access article distributed under the terms of the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License (CC BY NC ND 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content