Acta Univ. Agric. Silvic. Mendelianae Brun. 2016, 64(2), 449-453 | DOI: 10.11118/actaun201664020449

Risk Assessment of Handling Loads in Production Process

Erika Jankajová1, Martin Kotus1, Tomáš Holota1, Martin Zach2
1 Department of Quality and Engineering Technologies, Faculty of Engineering, Slovak University of Agriculture in Nitra, Tr. A. Hlinku 2, 949 76 Nitra, Slovak Republic
2 Expert Engineering Department, Institute of Lifelong Learning, Mendel University in Brno, Zemědělská 1, 613 00 Brno, Czech Republic

This paper deals with the evaluation of risks in the production process. The possible hazards were determined in the production of plastic windows and security measures were proposed. The level of risk were evaluated by using the extended point method, where were defined the probability and consequence of events as well as the opinion of the evaluator. The level of the risk is calculated as the multiplication of these three parameters and is classified into categories: Negligible, moderate, precarious, Adverse and unacceptable. The levels of hazard and safety measures are defined for employees for the manual handling of loads. The highest level of the risk (precarious) was achieved in danger of spine injury, where the risk cannot be accepted without protective measures. Other monitored threats (overload, wrick, fall of the load etc.) are classified in negligible risk or moderate risk that is acceptable or acceptable in increased attention. By compliance of suggested precautions it is possible to achieve the minimization of health threats of employees at work.

Keywords: security, risk, burden/load, risk, point method, danger

Prepublished online: May 4, 2016; Published: May 1, 2016  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Jankajová, E., Kotus, M., Holota, T., & Zach, M. (2016). Risk Assessment of Handling Loads in Production Process. Acta Universitatis Agriculturae et Silviculturae Mendelianae Brunensis, 64(2), 449-453. doi: 10.11118/actaun201664020449
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. BURDA, M., ČIČO, P., BUJNA, M. 2010. Posúdenie rizika pracovného miesta komplexnou metódou. In: Kvalita a spoľahlivosť technických systémov 2010. Nitra: SPU.
    2. GIRMANOVÁ, L., MIKLOŠ, V., PALFY, P., PETRÍK, J., SÜTŐOVÁ, A., ŠOLC, M. 2009. Nástroje a metódy manažérstva kvality. Košice: TU Elfa.
    3. INGALDI, M., LESTYÁNSZKA ŠKŮRKOVÁ, K. 2013. Environmental management in Polish companies. In: Manažérstvo životného prostredia. Žilina: STRIX.
    4. INGALDI, M., LESTYÁNSZKA ŠKŮRKOVÁ, K. 2014. Company strategy determination in food company using SWOT method. Acta Technologica Agriculturae, 3(2014: 66) -69. DOI: 10.2478/ata-2014-0015 Go to original source...
    5. KONSTANCIAK, M. 2012. Analysis of technological strategies on the example of the production of the tramway wheels. Archives of Materials Science and Engineering, 57(2): 69-74.
    6. KREDATUSOVÁ, M., BUJNA, M. 2010. Identifikácia a analýza ohrozenia vo vybranom procese. In: Najnovšie trendy v poľnohospodárstve, v strojárstve a odpadovom hospodárstve. Nitra: SPU.
    7. MAJLINGOVÁ, A., ORAVEC, M., ŠOLC, M., GALLA, Š. 2013. Modification of procedure to initiate the solids according to EN 60695-2-10 for materials used in historic buildings. European Journal of Environmental and Safety Sciences, 1(1): 8-12.
    8. MATISKOVÁ, D. 2013a. Selected methods from quality and automation of management production. Brno: Tribun.
    9. MATISKOVÁ, D. 2013b. Požiadavky na systémy manažérstva kvality vo výrobných podnikoch. In: Posterus.sk, 6(7): 1-7.
    10. MATISKOVÁ, D. 2013c. Strategické plánovanie - základ kvality riadenia podniku. Kvalita, 21(1): 37-40.
    11. PAULIČEK, T., ČIČO, P. 2010. Aplikácia metódy FMEA na proces výroby. In: Najnovšie trendy v poľnohospodárstve, v strojárstve a odpadovom hospodárstve. Nitra: SUA.
    12. PÍĽA, J., ADAMČIK, F., KORBA, P., ANTOŠKO, M. 2014. Safety Hazard and Risk in Slovak Aviation Regulations. Our Sea, International Journal of Maritime Science and Technology, 61(1-2): 27-30.
    13. ŠOLC, M., MARKULIK, Š., GRAMBALOVÁ, E. 2013. Quality of refractory materials in the technological process. Advanced Materials Research, 524(527): 2026-2030. Go to original source...
    14. VOTAVA, J. 2013a. Protection of welded joints against corrosion degradation. Acta Universitatis Agriculturae et Silviculturae Mendelianae Brunensis, 61(6): 1897-1904. DOI: 10.11118/actaun201361061897 Go to original source...
    15. VOTAVA, J. 2014. Usage of abrasion-resistant materials in agriculture. Journal of Central European Agriculture, 15(2): 119-128. DOI: 10.5513/JCEA01/15.2.1462 Go to original source...
    16. VOTAVA, J. 2013b. Corrosion resistance of water-thinnable paint systems. Journal of Central European Agriculture, 14(4): 1271-1278. DOI: 10.5513/JCEA01/14.4.1338 Go to original source...

    This is an open access article distributed under the terms of the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License (CC BY NC ND 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content