Acta Univ. Agric. Silvic. Mendelianae Brun. 2015, 63(1), 101-105 | DOI: 10.11118/actaun201563010101

A Research About Wear-resistance of Applied Layers Obtained by Gas Metal Arc Overlaying Process with Increased Wire Electrode Vibrating Frequency

Mitko Nikolov1, Iliya Todorov1, Martin Zach2, Pavel Máchal3, Jan Mareček4
1 Angel Kanchev' University of Ruse, Department of Repairing, Reliability, Mechanism, Machines, Logistic and Chemical technologies, ul. Studentska 8, Ruse, Bulgaria
2 Expert Engineering Department, Institute of Lifelong Learning, Mendel University in Brno, Zemědělská 1, 613 00 Brno, Czech Republic
3 Department of Project Management, Faculty of Regional Development and International Studies, Mendel University in Brno, Zemědělská 1, 613 00 Brno, Czech Republic
4 Department of Agriculture, Food and Environmental Engineering, Faculty of Agronomy, Mendel University in Brno, Zemědělská 1, 613 00 Brno, Czech Republic

The aim of the research is related to the influence of the vibration's frequency increasing upon wear-resistance of the applied layers. Wear-resistance is one of the most important properties of the materials that is considered as criteria about durability and reliability of the details of agricultural equipment and machinery.

Keywords: friction, wear-resistance, overlaying, gas metal overlaying process
Grants and funding:

The research was performed receiving support within "OP VK - CZ.1.07/2.3.00/30.0031 Postdoktorské pozice v technických aekonomických oborech na MENDELU".

Prepublished online: March 14, 2015; Published: April 1, 2015  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Nikolov, M., Todorov, I., Zach, M., Máchal, P., & Mareček, J. (2015). A Research About Wear-resistance of Applied Layers Obtained by Gas Metal Arc Overlaying Process with Increased Wire Electrode Vibrating Frequency. Acta Universitatis Agriculturae et Silviculturae Mendelianae Brunensis, 63(1), 101-105. doi: 10.11118/actaun201563010101
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. GARKUNOV, D. N. 2002. Tribotehnika - konstruirovanie, izgotovlenie, ekspluatacia mashin. Moskow: Izdatelstvo MCXA.
    2. KANGALOV, P. 2012. Defectological analysis of engine crankshafts in the automotive industry. In: Scientific thesis of University of Ruse, 51(1.1): 231-235.
    3. NIKOLOV, M., TONCHEV, G. 1995. Influence of the welding speed upon electrical parameters of the process during gas metal overlaying in CO2 shield. In: AMTECH '95. Ruse. Vol. 2: 163-168.
    4. TODOROV, I., NIKOLOV, M. 2012. Hardfacing process optimization with increased wire electrode frequency through methods of mathematical statistics. In: MENDELTECH INTERNATIONAL 2012 - INTERNATIONAL SCIENTIFIC CONFERENCE. Brno.
    5. TONCHEV, G. P., STANEV, L. 1979. Study on the distribution of components of tractors YMZ-6L and MTZ-80 by structural characteristics. In: Scientific thesis of University of Ruse, 21(5): 123-126.
    6. TONCHEV, G., NIKOLOV, M., STOJANOV, V., KANGALOV, P. 1996. A comparison research of different frictional pairs during sliding friction. In: Nadezhdnost, 96. Sofija. Chast III: 45-50.

    This is an open access article distributed under the terms of the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License (CC BY NC ND 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content