Acta Univ. Agric. Silvic. Mendelianae Brun. 2013, 61(5), 1313-1319 | DOI: 10.11118/actaun201361051313

Design of a laboratory hydraulic device for testing of hydraulic pumps

Pavel Máchal1, Zdenko Tkáč2, Ján Kosiba2, Juraj Jablonický2, Ľubomír Hujo2, Marián Kučera3, Juraj Tulík2
1 Mendel University in Brno, Institute of Lifelong Learning, Department of Expert Engineering, Zemědělská 5, 613 00 Brno, Czech Republic
2 Department of Transport and Handling, Faculty of Engineering, Slovak University of Agriculture in Nitra, Tr. A. Hlinku 2, 949 76 Nitra. Slovakia
3 Faculty of environmental and manufacturing technology, Technical University in Zvolen. Ul. T. G. Masaryka 24, 960 53 Zvolen, Slovakia

The present contribution deals with solves problem of research of testing device to monitor of hydrostatic pumps durability about dynamic loading under laboratory conditions. When carrying out the design of testing device are based on load characteristics of tractor hydraulic circuit, the individual characteristics of hydraulic components and performed calculations. Load characteristics on the tractors CASE IH Magnum 310, JOHN DEERE 8100, ZETOR FORTERRA 114 41 and Fendt 926 Vario were measured. Design of a hydraulic laboratory device is based on the need for testing new types of hydraulic pumps or various types of hydraulic fluids. When creating of hydraulic device we focused on testing hydraulic pumps used in agricultural and forestry tractors. Proportional pressure control valve is an active member of the hydraulic device, which provides change of a continuous control signal into relative pressure of operating fluid. The advantage of a designed hydraulic system is possibility of simulation of dynamic operating loading, which is obtained by measurement under real conditions, and thereby creates laboratory conditions as close to real conditions as possible. The laboratory device is constructed at the Department of Transport and Handling, Faculty of Engineering, Slovak University of Agriculture in Nitra.

Keywords: tractor, hydraulic pump, pressure, proportional pressure control valve
Grants and funding:

Supported by the Ministry of Education of the Slovak Republic, Project VEGA 1/0857/12 Reduction of unfavourable impacts of agricultural and transport machinery on the environment.

Received: May 7, 2013; Published: September 28, 2013  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Máchal, P., Tkáč, Z., Kosiba, J., Jablonický, J., Hujo, Ľ., Kučera, M., & Tulík, J. (2013). Design of a laboratory hydraulic device for testing of hydraulic pumps. Acta Universitatis Agriculturae et Silviculturae Mendelianae Brunensis, 61(5), 1313-1319. doi: 10.11118/actaun201361051313
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. DRABANT, Š. et al., 2008: Meranie a skúšanie hydrostatických prvkov a systémov (Measurement and testing of hydraulic devices and systems). Nitra: SUA in Nitra, s. 263. ISBN 978-80-552-0008-8
    2. HILL, T., LEWICKY, P., 2006: Statistic: Method and Applications. Tulsa, USA: StatSoft, Inc., 813 p. ISBN 1-884233-59-7.
    3. HUJO, Ľ., KOSIBA, J., JABLONICKÝ, J., TULÍK, J., 2012: Load characteristics of three-point tractor linkage. In: Naučni trudove: zemedelska technika i technologii, agrarni nauki i veterinarna medicina, remont i nadeždnosť., 51, 1.1: 172-176. ISSN 1311-3321.
    4. KUČERA, M., RÉDL, J., 2008: Vplyv podmienok experimentu na tribologické vlastnosti vybraných materiálov (Effects of Experimental Conditions on Tribologic Properties of Selected Materials). Acta technologica agriculturae, 1: 98-104. ISSN 1335-2555.
    5. KUČERA, M., ROUSEK, M., 2005: Environmentally compatible hydraulic oils for hydraulic components of mobile machinery. In: Proc. Conf. Hydraulic Mechanisms of Mobile Technique. Nitra: SUA in Nitra, 66-67. ISBN 80-8069-601-2.
    6. MAJDAN, R. et al., 2012: Zaťažovanie ekologických kvapalín prevádzkovým tlakom v laboratórnych podmienkach. (The loading of biodegradable fluid with operating load under laboratory conditions). Acta Facultatis Technicae, 17, 2: 83-92. ISSN 1336-4472 MAJDAN, R., 2010: Simulácia tlakového rázu v hydraulickom obvode. (Simulation of pressure impact in the hydraulic cirsuit). In: XII. International conference of young scientists 2010. Nitra: Faculty of Engineering SUA, 119-123. ISBN 978-80-552-0441-3.
    7. MAJDAN, R., CVÍČELA, P., BOHÁT, M., IVANIŠOVÁ, K., 2008: The observation of hydrostatic pump deterioration during the durability test according to hydraulic fluids contamination. In: X. International conference of young scientists 2008. Prague: Czech University of Life Sciences Prague, 147-153. ISBN 978-80-213-1812-0.
    8. TKÁČ, Z., ŠKULEC, R., 2002: Aplikácia bioodbúrateľného oleja v prevodovom a hydraulickom systéme traktora (Application of bio-degradable oil in the gear and hydraulic system of the tractor). Acta Mechanika, 2: 297-270. ISSN 1335-2393.
    9. TKÁČ, Z., DRABANT, Š., MAJDAN, R., CVÍČELA, P., 2008a: Testing stands for laboratory tests of hydrostatic pumps of agricultural machinery. Research in agricultural engineering, 54, 4: 183-191. ISSN 1212-9151. Go to original source...
    10. TKÁČ, Z. et al., 2008b: The Testing Device for Durability Tests of Hydrostatic Pumps. Acta hydraulica et pneumatica, 10, 1: 29-34. ISSN 1336-7536.
    11. TKÁČ, Z., DRABANT, Š., MAJDAN, R., CVÍČELA, P., 2008: Testing stands for laboratory tests of hydrostatic pumps of agricultural machinery. Research in agricultural engineering, 54, 4: 183-191. ISSN 1212-9151. Go to original source...
    12. TKÁČ, Z. et al., 2010: Hodnotenie vlastností hydraulických kvapalín na základe skúšok s použitím hydrogenerátora (Evaluation of the properties of hydraulic fluids based tests with using hydrostatic pump). Nitra: SUA in Nitra, 112 s. ISBN 978-80-552-0338-6.
    13. TURZA, J., KOPILÁKOVÁ, B., 2011: Kombinovaný stend pre meranie hydraulických prvkov (Combined resources for hydraulics elements measuruing). In: Management of fluid systems 2011. Žilina: Hydropneutech, 119-126. ISBN 978-80-968150-9-8.

    This is an open access article distributed under the terms of the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License (CC BY NC ND 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content