Acta Univ. Agric. Silvic. Mendelianae Brun. 2016, 64(3), 835-839 | DOI: 10.11118/actaun201664030835

Protective Woodcutting Tool Coatings

Svetlana D. Latushkina1, Pavel V. Rudak2, Dmitri V. Kuis2, Oxana G. Rudak3, Olga I. Posylkina1, Olga Y. Piskunova2, Ján Kováč4, Jozef Krilek4, ©tefan Barcík5
1 Physical Technical Institute, the Academy of Sciences, the Republic of Belarus, Minsk, Kuprevicha St., Minsk, 220141, Belarus
2 Department of Materials Science and Metal Technology, Belarussian State Technological University, Sverdlova str. 13a, 220006, Minsk, Belarus
3 Department of Technology and Design of Wood Products, Belarussian State Technological University, Sverdlova str. 13a, 220006, Minsk, Belarus
4 Department of Environmental and Forestry Machine, Faculty of Environmental and Manufacturing Technology, Technical University in Zvolen, T. G. Masaryka 24, 960 53 Zvolen, Slovak Republic
5 Department of Machinery Control and Automation, Faculty of Environmental and Manufacturing technology, Technical University in Zvolen, T. G. Masaryka 24, 960 53 Zvolen, Slovak Republic

The modern woodworking industry applies resource-saving, environmentally appropriate technologies, providing both the metal removal performance enhancement and functioning with the optimal economic factors. Progressive cutting parameters require the application of the high-reliability cutting tools, eliminating machine-tool equipment standstill and increased cost of the expensive tool materials. In this paper it is suggested to increase the wood-cutting tool efficiency by means of the vacuum-arc separated coating deposition process optimization.
The droplets are one of the main problems while generating vacuum-arc coatings, and they have a bad influence on the quality and operational coatings characteristics. The application of the separated system, allowing minimize the droplets content, is one of the most promising ways to solve this problem. Vacuum-arc deposition technique was used in this work to generate multicomponent coatings. The coatings deposition was directly carried out on the modernized vacuum-arc plant, equipped by Y-shaped macroparticles separator.

Keywords: tool coating, morphology, woodcutting, physical and mechanical properties, cutting plates

Prepublished online: July 4, 2016; Published: July 1, 2016  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Latushkina, S.D., Rudak, P.V., Kuis, D.V., Rudak, O.G., Posylkina, O.I., Piskunova, O.Y., ... Barcík, ©. (2016). Protective Woodcutting Tool Coatings. Acta Universitatis Agriculturae et Silviculturae Mendelianae Brunensis, 64(3), 835-839. doi: 10.11118/actaun201664030835
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. ČIERNA, H., «AVODOVÁ, M. 2013. Using the design of experiment method to evaluate quality of cuts after cutting aluminum alloy by AWJ. Manufacturing technology: journal for science, research and production, 13: 303-307. Go to original source...
    2. GRIGORIEV, S. N. 2009. Methods of cutter power increasing. Moscow: Machine building.
    3. HANES, T. et al. 2014. Coating surface roughness measurement made on coining dies. Manufacturing technology: journal for science, research and production, 14: 309-317. Go to original source...
    4. HOLM, B., AHUJA, R., LI, S., JOHANSSON, B. 2002. Theory of the ternary layered system Ti-Al-N. J. Appl. Phys., 91: 9874-9877. DOI: 10.1063/1.1476076 Go to original source...
    5. KOVÁČ, J., KRILEK, J., 2011. The possibilities for measurement of saw blades wearing. Acta Universitatis Agriculturae et Silviculturae Mendelianae, 59: 137-143. DOI: 10.11118/actaun201159050137 Go to original source...
    6. SHTANSKII, D. V., LEVASHOV, E. A. 2001. Multicomponent nanosrtuctural thin films: issues and decisions. Nonferrous metallurgy, 3: 52-62.
    7. TENTARDINI, E. K., AGUZZOLI, C., CASTRO, M. et al. 2008. Reactivity between aluminum between (Ti,Al)N coatings for casting dies. Thin Solid Films., 516: 3062-3069. DOI: 10.1016/j.tsf.2007.10.088 Go to original source...
    8. VERESHCHAKA, A. S. 2007. Modern technologies of machine building. Kharkov.

    This is an open access article distributed under the terms of the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License (CC BY NC ND 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content